/**
* \file
*
* \brief KSZ8051MNL (Ethernet PHY) driver for SAM.
*
* Copyright (c) 2013 Atmel Corporation. All rights reserved.
*
* \asf_license_start
*
* \page License
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
*
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* 3. The name of Atmel may not be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* 4. This software may only be redistributed and used in connection with an
* Atmel microcontroller product.
*
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
* \asf_license_stop
*
*/
#ifndef ETHERNET_PHY_H_INCLUDED
#define ETHERNET_PHY_H_INCLUDED
#include "compiler.h"
#ifdef __cplusplus
extern "C" {
#endif
// IEEE defined Registers
#define GMII_BMCR 0x00 // Basic Control
#define GMII_BMSR 0x01 // Basic Status
#define GMII_PHYID1 0x02 // PHY Idendifier 1
#define GMII_PHYID2 0x03 // PHY Idendifier 2
#define GMII_ANAR 0x04 // Auto_Negotiation Advertisement
#define GMII_ANLPAR 0x05 // Auto_negotiation Link Partner Ability
#define GMII_ANER 0x06 // Auto-negotiation Expansion
#define GMII_ANNPR 0x07 // Auto-negotiation Next Page
#define GMII_ANLPNPAR 0x08 // Link Partner Next Page Ability
//#define GMII_1000BTCR 9 // 1000Base-T Control // Reserved
//#define GMII_1000BTSR 10 // 1000Base-T Status // Reserved
#define GMII_AFECR1 0x11 // AFE Control 1
//#define GMII_ERDWR 12 // Extend Register - Data Write Register
//#define GMII_ERDRR 13 // Extend Register - Data Read Register
//14 reserved
#define GMII_RXERCR 0x15 // RXER Counter
#define PHY_REG_01_BMSR 0x01 // Basic mode status register
#define PHY_REG_02_PHYSID1 0x02 // PHYS ID 1
#define PHY_REG_03_PHYSID2 0x03 // PHYS ID 2
#define PHY_REG_04_ADVERTISE 0x04 // Advertisement control reg
#define PHY_REG_05_LPA 0x05 // Link partner ability reg
#define PHY_REG_06_ANER 0x06 // 6 RW Auto-Negotiation Expansion Register
#define PHY_REG_07_ANNPTR 0x07 // 7 RW Auto-Negotiation Next Page TX
#define PHY_REG_08_RESERVED0 0x08 // 0x08..0x0Fh 8-15 RW RESERVED
#define PHY_REG_10_PHYSTS 0x10 // 16 RO PHY Status Register
#define PHY_REG_11_MICR 0x11 // 17 RW MII Interrupt Control Register
#define PHY_REG_12_MISR 0x12 // 18 RO MII Interrupt Status Register
#define PHY_REG_13_RESERVED1 0x13 // 19 RW RESERVED
#define PHY_REG_14_FCSCR 0x14 // 20 RO False Carrier Sense Counter Register
#define PHY_REG_15_RECR 0x15 // 21 RO Receive Error Counter Register
#define PHY_REG_16_PCSR 0x16 // 22 RW PCS Sub-Layer Configuration and Status Register
#define PHY_REG_17_RBR 0x17 // 23 RW RMII and Bypass Register
#define PHY_REG_18_LEDCR 0x18 // 24 RW LED Direct Control Register
#define PHY_REG_19_PHYCR 0x19 // 25 RW PHY Control Register
#define PHY_REG_1A_10BTSCR 0x1A // 26 RW 10Base-T Status/Control Register
#define PHY_REG_1B_CDCTRL1 0x1B // 27 RW CD Test Control Register and BIST Extensions Register
#define PHY_REG_1B_INT_CTRL 0x1B // 27 RW KSZ8041NL interrupt control
#define PHY_REG_1C_RESERVED2 0x1C // 28 RW RESERVED
#define PHY_REG_1D_EDCR 0x1D // 29 RW Energy Detect Control Register
#define PHY_REG_1E_RESERVED3 0x1E //
#define PHY_REG_1F_RESERVED4 0x1F // 30-31 RW RESERVED
#define PHY_REG_1E_PHYCR_1 0x1E //
#define PHY_REG_1F_PHYCR_2 0x1F //
#define PHY_SPEED_10 1
#define PHY_SPEED_100 2
#define PHY_SPEED_AUTO (PHY_SPEED_10|PHY_SPEED_100)
#define PHY_MDIX_DIRECT 1
#define PHY_MDIX_CROSSED 2
#define PHY_MDIX_AUTO (PHY_MDIX_CROSSED|PHY_MDIX_DIRECT)
#define PHY_DUPLEX_HALF 1
#define PHY_DUPLEX_FULL 2
#define PHY_DUPLEX_AUTO (PHY_DUPLEX_FULL|PHY_DUPLEX_HALF)
typedef struct _SPhyProps {
unsigned char speed;
unsigned char mdix;
unsigned char duplex;
unsigned char spare;
} SPhyProps;
const char *phyPrintable (const SPhyProps *apProps);
extern SPhyProps phyProps;
#define GMII_OMSOR 0x16 // Operation Mode Strap Override
#define GMII_OMSSR 0x17 // Operation Mode Strap Status
#define GMII_ECR 0x18 // Expanded Control
//#define GMII_DPPSR 19 // Digital PMA/PCS Status
//20 reserved
//#define GMII_RXERCR 21 // RXER Counter Register
//22-26 reserved
#define GMII_ICSR 0x1B // Interrupt Control/Status
//#define GMII_DDC1R 28 // Digital Debug Control 1 Register
#define GMII_LCSR 0x1D // LinkMD Control/Status
//29-30 reserved
#define GMII_PCR1 0x1E // PHY Control 1
#define GMII_PCR2 0x1F // PHY Control 2
/*
//Extend Registers
#define GMII_CCR 256 // Common Control Register
#define GMII_SSR 257 // Strap Status Register
#define GMII_OMSOR 258 // Operation Mode Strap Override Register
#define GMII_OMSSR 259 // Operation Mode Strap Status Register
#define GMII_RCCPSR 260 // RGMII Clock and Control Pad Skew Register
#define GMII_RRDPSR 261 // RGMII RX Data Pad Skew Register
#define GMII_ATR 263 // Analog Test Register
*/
// Bit definitions: GMII_BMCR 0x00 Basic Control
#define GMII_RESET (1 << 15) // 1= Software Reset; 0=Normal Operation
#define GMII_LOOPBACK (1 << 14) // 1=loopback Enabled; 0=Normal Operation
#define GMII_SPEED_SELECT (1 << 13) // 1=100Mbps; 0=10Mbps
#define GMII_AUTONEG (1 << 12) // Auto-negotiation Enable
#define GMII_POWER_DOWN (1 << 11) // 1=Power down 0=Normal operation
#define GMII_ISOLATE (1 << 10) // 1 = Isolates 0 = Normal operation
#define GMII_RESTART_AUTONEG (1 << 9) // 1 = Restart auto-negotiation 0 = Normal operation
#define GMII_DUPLEX_MODE (1 << 8) // 1 = Full duplex operation 0 = Normal operation
#define GMII_COLLISION_TEST (1 << 7) // 1 = Enable COL test; 0 = Disable COL test
//#define GMII_SPEED_SELECT_MSB (1 << 6) // Reserved
// Reserved 6 to 0 // Read as 0, ignore on write
// Bit definitions: GMII_BMSR 0x01 Basic Status
#define GMII_100BASE_T4 (1 << 15) // 100BASE-T4 Capable
#define GMII_100BASE_TX_FD (1 << 14) // 100BASE-TX Full Duplex Capable
#define GMII_100BASE_T4_HD (1 << 13) // 100BASE-TX Half Duplex Capable
#define GMII_10BASE_T_FD (1 << 12) // 10BASE-T Full Duplex Capable
#define GMII_10BASE_T_HD (1 << 11) // 10BASE-T Half Duplex Capable
// Reserved 10 to79 // Read as 0, ignore on write
//#define GMII_EXTEND_STATUS (1 << 8) // 1 = Extend Status Information In Reg 15
// Reserved 7
#define GMII_MF_PREAMB_SUPPR (1 << 6) // MII Frame Preamble Suppression
#define GMII_AUTONEG_COMP (1 << 5) // Auto-negotiation Complete
#define GMII_REMOTE_FAULT (1 << 4) // Remote Fault
#define GMII_AUTONEG_ABILITY (1 << 3) // Auto Configuration Ability
#define GMII_LINK_STATUS (1 << 2) // Link Status
#define GMII_JABBER_DETECT (1 << 1) // Jabber Detect
#define GMII_EXTEND_CAPAB (1 << 0) // Extended Capability
// Bit definitions: GMII_PHYID1 0x02 PHY Idendifier 1
// Bit definitions: GMII_PHYID2 0x03 PHY Idendifier 2
#define GMII_LSB_MASK 0x3F
#define GMII_OUI_MSB 0x0022
#define GMII_OUI_LSB 0x05
// Bit definitions: GMII_ANAR 0x04 Auto_Negotiation Advertisement
// Bit definitions: GMII_ANLPAR 0x05 Auto_negotiation Link Partner Ability
#define GMII_NP (1 << 15) // Next page Indication
// Reserved 7
#define GMII_RF (1 << 13) // Remote Fault
// Reserved 12 // Write as 0, ignore on read
#define GMII_PAUSE_MASK (3 << 11) // 0,0 = No Pause 1,0 = Asymmetric Pause(link partner)
// 0,1 = Symmetric Pause 1,1 = Symmetric&Asymmetric Pause(local device)
#define GMII_100T4 (1 << 9) // 100BASE-T4 Support
#define GMII_100TX_FDX (1 << 8) // 100BASE-TX Full Duplex Support
#define GMII_100TX_HDX (1 << 7) // 100BASE-TX Support
#define GMII_10_FDX (1 << 6) // 10BASE-T Full Duplex Support
#define GMII_10_HDX (1 << 5) // 10BASE-T Support
// Selector 4 to 0 // Protocol Selection Bits
#define GMII_AN_IEEE_802_3 0x0001 // [00001] = IEEE 802.3
// Bit definitions: GMII_ANER 0x06 Auto-negotiation Expansion
// Reserved 15 to 5 // Read as 0, ignore on write
#define GMII_PDF (1 << 4) // Local Device Parallel Detection Fault
#define GMII_LP_NP_ABLE (1 << 3) // Link Partner Next Page Able
#define GMII_NP_ABLE (1 << 2) // Local Device Next Page Able
#define GMII_PAGE_RX (1 << 1) // New Page Received
#define GMII_LP_AN_ABLE (1 << 0) // Link Partner Auto-negotiation Able
/**
* \brief Perform a HW initialization to the PHY and set up clocks.
*
* This should be called only once to initialize the PHY pre-settings.
* The PHY address is the reset status of CRS, RXD[3:0] (the GmacPins' pullups).
* The COL pin is used to select MII mode on reset (pulled up for Reduced MII).
* The RXDV pin is used to select test mode on reset (pulled up for test mode).
* The above pins should be predefined for corresponding settings in resetPins.
* The GMAC peripheral pins are configured after the reset is done.
*
* \param p_gmac Pointer to the GMAC instance.
* \param uc_phy_addr PHY address.
* \param ul_mck GMAC MCK.
*
* Return GMAC_OK if successfully, GMAC_TIMEOUT if timeout.
*/
uint8_t ethernet_phy_init(Gmac *p_gmac, uint8_t uc_phy_addr, uint32_t ul_mck);
/**
* \brief Get the Link & speed settings, and automatically set up the GMAC with the
* settings.
*
* \param p_gmac Pointer to the GMAC instance.
* \param uc_phy_addr PHY address.
* \param uc_apply_setting_flag Set to 0 to not apply the PHY configurations, else to apply.
*
* Return GMAC_OK if successfully, GMAC_TIMEOUT if timeout.
*/
uint8_t ethernet_phy_set_link(Gmac *p_gmac, uint8_t uc_phy_addr,
uint8_t uc_apply_setting_flag);
/**
* \brief Issue an auto negotiation of the PHY.
*
* \param p_gmac Pointer to the GMAC instance.
* \param uc_phy_addr PHY address.
*
* Return GMAC_OK if successfully, GMAC_TIMEOUT if timeout.
*/
uint8_t ethernet_phy_auto_negotiate(Gmac *p_gmac, uint8_t uc_phy_addr);
/**
* \brief Issue a SW reset to reset all registers of the PHY.
*
* \param p_gmac Pointer to the GMAC instance.
* \param uc_phy_addr PHY address.
*
* \Return GMAC_OK if successfully, GMAC_TIMEOUT if timeout.
*/
uint8_t ethernet_phy_reset(Gmac *p_gmac, uint8_t uc_phy_addr);
typedef struct xPHY_PROPS {
signed char phy_result;
uint32_t phy_params;
uint32_t phy_stat1;
uint32_t phy_stat2;
unsigned char phy_chn;
} PhyProps_t;
extern PhyProps_t phy_props;
#ifdef __cplusplus
} /* extern "C" */
#endif
#endif /* #ifndef ETHERNET_PHY_H_INCLUDED */